CaseLens HELP

← All guides

Phone app: take job photos, notes and moisture readings with no signal

Save photos, notes and moisture readings on a Pro job in a basement or crawlspace with no signal, then watch them upload when you're back in signal. About 5 minutes.

For: CaseLens phone app (not CaseLens Pro in a browser) · Last reviewed:

Watch it (2:05, no sound)

Before you start

Step by step

  1. 1Open the app with no signal

    With no signal, the line at the top starts with No signal. Your jobs are still listed: Showing the list saved on this phone says when the app last loaded them. Tap the job.

    Open the app with no signal
    Tap the picture to see it full size.
  2. 2Take a photo

    Under Photos, tap Take a photo to open the camera, or Or choose from your photos for ones you took earlier (you can pick several). Type the Room or area and a Caption saying exactly what it shows, like "Pin meter on the sill plate, north side".

    Take a photo
    Tap the picture to see it full size.
  3. 3Save the photo

    Tap Save photos. The app works out the photo's fingerprint and reads its time, position and camera from the file now, on the phone, so they're recorded as they were when you took it.

    Save the photo
    Tap the picture to see it full size.
  4. 4It's saved on the phone

    You'll see 1 photo saved on this phone. near the bottom, under Open the full job in CaseLens Pro, and it's listed under Saved on this phone, not uploaded yet with Waiting for signal. Keep going: everything you save waits there.

    It's saved on the phone
    Tap the picture to see it full size.
  5. 5Write a note

    Scroll up to Note. Write what you saw, did or were told, then tap Save note. The note keeps the time you wrote it, even though it reaches CaseLens later.

    Write a note
    Tap the picture to see it full size.
  6. 6Enter moisture readings

    Under Moisture readings, Date is today. Fill in Meter and mode and Meter last calibrated, then a reading for each point you took (each box shows the point, its room and the unit; goal is its dry standard). Leave a point blank if you didn't read it. Tap Save readings; you'll see Readings saved on this phone.

    Enter moisture readings
    Tap the picture to see it full size.
  7. 7Check what's waiting

    Everything for this job is listed under Saved on this phone, not uploaded yet, each with the time you made it. The line at the top of the screen counts them (3 saved on this phone, will upload when you have signal).

    Check what's waiting
    Tap the picture to see it full size.
  8. 8Back in signal

    When the phone has signal again, the app uploads everything by itself, in the order you made it, while it's open. You don't need to tap anything. The line turns to Everything is uploaded. and the waiting list goes away. Open the app for a moment after you come up, so it can upload.

    Back in signal
    Tap the picture to see it full size.
  9. 9See it on the job

    Tap Open the full job in CaseLens Pro to see the photos, note and readings on the job in Pro. Each one shows when you made it on the phone and when it reached CaseLens.

    See it on the job
    Tap the picture to see it full size.

If something goes wrong

"This job isn't on this phone yet. Connect once and open it from the list."
The job was added after the app last had signal. Get signal, open the app's list once, then the job works offline.
"No reading points on this job yet."
Add the reading points to the job in CaseLens Pro, then open the job in the app once with signal.
"The meter's calibration date can't be after the reading date."
Check Meter last calibrated and Date.
"Readings should be numbers."
Type just the number, like 38 or 14.5, without the unit.
Something says "Couldn't upload"
CaseLens refused it; it's kept on the phone. See Check the upload queue: retry or remove what's waiting.

What's next